Search results

Fo For daily commute mt's are very good, but it doesn't scream like fz6's inline 4, ive ridden xsr900 and i fall inlove with that bike has lots of torque down low but the price is too much for me

R Yes those twin undertail exhaust i love it!

Its really hard to decide, especially the price difference between the two isn't that far. And the FZ1 has a lot of aftermarket tuning parts compared to S1 FZ6. Its hard to let go of this bike , my first inline 4 bike.

Ive owned my FZ6N in less than a year and most of those times was me rebuilding the bike from junk to where it is now. Back from the dead! Lately Ive been eyeing its bigger brother FZ1N I saw one personally but havent ridden one. Im having 2nd thoughts about this because i havent really ridden...

I love your garage setup, i wish i had one like yours. I like it when i can leave the mess and come back and nothings changed. A place where you can be yourself sure is a happy place! Ive just finished rebuilding the engine of my monster. The paint on this sucks the only way to get them...

Another update! I did the resistor trick. Runs well and no CEL But problem still exists Im still thinking why i didn't do TPS test when the problem occurs Well it turns out my new chinese TPS is affected by heat soak Tps reading when Cold engine 16 When hot 25 Before replacing the tps, i...

I I lift up the tank then unplug the iat socket while running(problem occurs). CEL Lit when i unplugged the socket Put multimeter set to ohms and poked the probe to the 2pin sensor. Thats how i got the ohms reading

Update It happened again i noticed when im at slow traffic and sometimes get stuck in traffic light it occurs. when im cruising at a good speed and the weather is cold it does not occur. I tested my IAT sensor for resistance when its hot and the problem occurs it shows very low ohms and...

Ive been reading more and more about this mod and it got me intrigued that i want it! I have a S1 still with cat but with slip ons The thing that really bothers me is the off throttle response specially when in mid corner delayed throttle response making it uncomfortable. Do i have to tinker...

I cleaned the sync block and the throttle bodies before, and yes i set the base 3/4 out and sync the TB's using vacuum gauges. Revving it steady at 3k rpm it all seemed to have the same vacuums.

Update I let the bike warmed up and turned the idle screw all the way to highest rpm it could get, and slowly turned it out until i reached 1300rpms and left it set , so far the problem hasn't occured yet

Back from the dead Dont mind the tires :p New set is yet to arrive

Thank you for the greetings and also for helping me "ALOT" Guys!!!

That'll be a great project bike, fully restored and for sure thats a keeper!

Yup a duck with valve guide issue However I wont do a full tear down, compression is good but oil is leaking past the valve seals,

An Any thoughts about this? I was out looking for parts on my new project when this happened I plan on tackling this when i finished rebuilding the engine.

I saw someone in my local market that sells surplus mosfet R/R which is from bike breakers and its selling like hotcakes mostly installed to honda cb400 I'll give it a try. Perhaps you could give me some tips what to look for. Parts number or codes maybe?

Yes ive checked my stator 3 white wires AC with in spec 70-80v at 5k rpm 14.4v at R/R voltage (red/black wire) Im thinking maybe that RR is overheating and not function as it should, i havent tested the R/R while the rpm is dropped like in the video. Are MOSFETS any good? Since i have doubts...

Ok so i encountered this problem twice and i cant seem to find whats causing this. The bike ran fine no jerking or sudden power loss . Bike revs fine and no delay when i twist the throttle It only happens when its hot outside How ever when i let the bike rest for a minute or so, it comes back...

Out of topic If you disconnect your fuel hose from your tank, does the gasoline from tank dripping slowly? I notice mine did it and i think its normal thata ita slowly dripping