email me [email protected]
Dramatically improved the comfort on my FZ6. These are brand new, never been installed (they were a second set I had). $30 shipped.
These risers are placed between the factory bar clamps and will raise the handlebars 1" upward and 1.25" backward while retaining...
I have been converting my FZ6 to a street fighter and have been trying to find a solution to mount mirrors on my handlebar ends, but it seems that all of the mirrors i find are for hollow handlebars while the FZ6 has threaded ends, which i am assuming is uncommon. I searched for a few hours...
Offering a single OEM bar end
Sold my Fz6 - no longer have a use for it.
It has some scratches and could use a repaint but otherwise is in very good shape. no rash or anything.
Pay for fair shipping and it is yours
Hi all
I'm wanting to drastically change the ridding position so I'm sitting in a more upright position.
I have the bars in want, I've seen bar risers on SW Motech that look decent.
The problem I have is all the current cable lengths are far too short.
Does any one have any advice on how...
Bar end weight spacers for factory weights and bar end mirrors:
Cut the end off an old/bent handle bar:
Removed the center pipe that threaded.
Cut the inner pipe down to the width of my bar end mirror clamps:
After cleaning up the cuts and the threads, threaded them onto the factory bar...
Hey everyone. I had a humpty dumpty moment with my bike today. Loading it into the truck bed, had a slip and toppled over to right side. It damaged a lot to the naked eye, and I am going to do a full tear down to see if there is any hidden damage. Its a 2008.
So far I know I will need these...
Very nice, low mileage FZ6 (8089 miles). Comes with almost new Michelin Pilot Road 4 tires, heated grips, HVRP bar ends (less vibration), bar risers for a more comfortable position, custom touring seat with removable backrest, Denali DM micro LED driving lights, Yamaha touring windshield with...
Aloha to all, I've been searching different topics for a few days and couldn't find anything that resembles my problem. I've purchased a 2006 FZ6 with 7,800 miles which is all stock with the exception of bars, grips, levers and a 48t rear sprocket. I've only put about 100 miles on it but a few...
hey i did a lil crash with my buike i fixed it as new but i have a problem
my handlebar does not match the front wheel direction
how i can fix this
the handle bar is new not bent
ANGLŲ K. – APTIKTA
ANGLŲ
Hi all, i'am new on here, just didnt find any thread about my prob.. So, i land my bike for my friend, he droped it and now iam having issues, allready replaced stearing bar, stearing bar bearing, one slider... but it looks to me that my stearing now isnt...
Lightly used, great condition. Some miniscule scratches, only visible when photographed the way I did. Not visible when installed and used on bike. Entire set retails for $150 altogether. Asking $60 shipped.
I also have a set of stock Yamaha 16mm threaded bar ends, painted black, that were...
Hey there,
Apologies for another bar ends thread but I can't seem to find the info I'm looking for. I'm looking to throw some of 7/8" Handle Bar End Mirrors For Yamaha XJR1300 / XJ6 / V-max / MT-01/ FZ1 / FZ6 on my handlebars as I slowly prepare for my full conversion. I'd love to throw these...
As I prepare for my upcoming upgrade spree I wanted to get some feedback on handlebars.
I purchased the bike with 1" Pro Taper bar risers and aluminum handle bars, and I'm not a big fan.
They may have fit the previous owner well but feel too wide for me. This problem may be compounded...
Hey folks, as mentioned in the title Im looking for a left mirror assembly from an FZ6 as well as the bar end weights from an FZ1 (in good condition, no scuffs or scrapes.
I'm not on the forum much so the best way to get in touch quick is via PM which I'll see in my email. Thanks!
I am the 3rd owner of a 05 FZ6 and trying to extend the season as long as possible here in the NE and thus looking to install heated grips however it seems the allen bolt inside the bar end is stripped and I can't remove it. Tried inserting a torx bit of similar size, hammering it in and using...
So I finally got around to installing the FZ1 bar I've had sitting around for ages (thanks Raja) as well as some heated grips for the colder months. Holy crap I should have swapped the bars way before. It is so much more comfortable, and the steering feels much more direct. Less fatigue in my...
Hello everyone. I finally took the plunge on Friday night. After months of asking questions that you have all heard before and gathering parts, At last she is naked. Still a work in progress, wires to clean up, turn signals to mount and I'm not sure I like the speedo cover.
Other mods: CRG...
Hello, I have a small dilemma here.. I had bar end mirrors but one of them got damaged (bent screw) and I had to take them out.. now with them out I thought maybe I should install some new bar ends ..but those won't allow me to install bar end mirros anymore .. hmmm? I also have heated grips so...
Hi,
I'm looking for an FZ1 handlebar (or an aftermarket flat bar that can accommodate OEM bar ends - if such bars exist that is)
Please PM me, or post on this thread if you have one for sale.
Thanks
Shyam
I've been toying with the idea of a front brake protector for a while now and the Rizoma Proguard looks the business.
They also have a matching bar end for the left side.
However, I have read some posts that playing with the weight of the bar ends affects the handling and can cause...